Physicochemical study of microwave-synthesized organoclays

dc.contributor.authorYapar, Saadet
dc.date.accessioned2019-10-27T20:50:11Z
dc.date.available2019-10-27T20:50:11Z
dc.date.issued2009
dc.departmentEge Üniversitesien_US
dc.description.abstractIn this work, microwave-synthesized organoclays were prepared and the physicochemical properties examined due to the importance and wide range of organoclay applications. Previous research studies have reported the synthesis of new organoclays, however, almost the same synthesis procedures have been used except for the small changes in reactant addition rate, solvent, and temperature. The standard organoclay preparation method involving intercalation, washing and drying steps is a time-consuming process with the intercalation step taking a few hours. Although it is a good laboratory method, the long time requirement for the synthesis forms a bottleneck in the industrial applications. In contrast to the conventional synthesis procedure, microwave irradiation makes it possible to complete the intercalation in a short time. Additionally the use of microwave for drying purposes will cause a further reduction in the time requirement. In this research, the organoclays were synthesized by using hexadecyltrimethylammonium bromide, a smectite from central Anatolia, and microwave irradiation. The organoclays were dried using freeze drying, microwave drying and oven drying. They were examined using X-ray diffraction, electron microscopy, IR spectroscopy, and thermal analysis to determine the effect of irradiation on the physicochemical properties. The d-spacings were determined to be 19.5 angstrom that is close to the values reported for the conventionally prepared organoclays. The results of FIR analysis reveal that the confined amine chains adopted all-trans conformation as in the case of the conventional organoclays. Application of microwave irradiation at 360W for 5 min is enough to achieve a 70% exchange efficiency which is comparable to the organic cation exchange efficiencies reported using conventional techniques. Except the surface morphology, drying conditions have no effect on the structural properties of organoclays. Therefore, it is concluded that the use of microwave irradiation in the intercalation step has the potentialities for industrial scale applications and microwave drying should also be considered in the last step of synthesis due to the very short drying time compared to other methods. (C) 2009 Elsevier B.V. All rights reserved.en_US
dc.description.sponsorshipDAADDeutscher Akademischer Austausch Dienst (DAAD); Institute of Technological Chemistry, Water and Geotechnology Division in the Research Center Karlsruhe, Germanyen_US
dc.description.sponsorshipThe author gratefully acknowledge the support of DAAD and the Institute of Technological Chemistry, Water and Geotechnology Division in the Research Center Karlsruhe, Germany.en_US
dc.identifier.doi10.1016/j.colsurfa.2009.04.032
dc.identifier.endpage81en_US
dc.identifier.issn0927-7757
dc.identifier.issn1873-4359
dc.identifier.issn0927-7757en_US
dc.identifier.issn1873-4359en_US
dc.identifier.issue01.Maren_US
dc.identifier.scopusqualityQ1en_US
dc.identifier.startpage75en_US
dc.identifier.urihttps://doi.org/10.1016/j.colsurfa.2009.04.032
dc.identifier.urihttps://hdl.handle.net/11454/42960
dc.identifier.volume345en_US
dc.identifier.wosWOS:000268059800011en_US
dc.identifier.wosqualityQ3en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherElsevier Science Bven_US
dc.relation.ispartofColloids and Surfaces A-Physicochemical and Engineering Aspectsen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectMicrowaveen_US
dc.subjectSmectiteen_US
dc.subjectOrganoclayen_US
dc.subjectSTAen_US
dc.subjectSEMen_US
dc.titlePhysicochemical study of microwave-synthesized organoclaysen_US
dc.typeArticleen_US

Dosyalar